straight joint
英 [streɪt dʒɔɪnt]
美 [streɪt dʒɔɪnt]
网络 直通接头; 电缆直线接头; 通缝; 直接头
双语例句
- The bones in the tail should feel straight and should reach to the hock joint or below.
尾骨直，而且延伸到飞节或更低的位置。 - Pull plastic sleeve straight off the joint flange.
径直将塑料套管从连接法兰中拔下。 - It utilizes advanced technology of straight screw thread joint, scientific concrete mix proportion of HPC, advanced technology of presses syrup in vacuum in construction.
该文主要论述了真空压浆技术的原理、优点、施工工艺和施工控制要点，并探讨了圆形池壁后张法预应力结构孔道压浆技术。 - The utility model relates to a wind dust collector for operating vehicles, is composed of an air intake pipe, a material discharge pipe, a straight tube, a rotary joint, and a dust collector device.
一种用于行驶车辆上的风力吸尘器，由进风管、排物管、直管、转向接头和吸尘器装置组成。 - Heb. 12:13 And make straight paths for your feet, that what is lame may not be put out of joint but rather may be healed.
来十二13也要为自己的脚把路径修直了，使瘸子不致脱臼，反得医治。 - Research on Compressive Behaviors of n-type block masonry with straight joint
同缝砌筑的N式砌块砌体受压性能研究 - Treatment of straight knee joint adhesion with combination of traditional Chinese and western medicine
伸直型伸膝装置粘连的中西医结合治疗 - Prevention and Control Measures of the Soaking of Straight Burying Cable Joint Box
直埋光缆接头盒浸水防治的措施 - Following the example of surplus joint of standard straight cylinder gear and axle, the article has explained that ANSYS Finite Element Analysis software can be applied to stress analysis of the surplus joint.
本文以标准直齿圆柱齿轮和轴的过盈配合为例，说明了ANSYS有限元分析软件在过盈配合联接安全核算中是可以适用的。 - CONCLUSION; ① The national outstanding female javelin athlete finally makes an effort at the stage javelin to get rid of instantaneous throwing, the left leg strongly straight pedal extends, which possibly attributes to the left knee joint flank meniscus damages.
结论：①国家优秀女子标枪运动员在最后用力阶段标枪出手瞬间，左腿强直蹬伸可能是造成左膝关节外侧半月板损伤的重要因素。 - This paper introduces the features of reinforcement rolled full-stress straight thread joint, expounds the construction techniques, operation procedures, quality detection requirements, and popularizing values of this techniques, and puts forward some matters needing attention in the construction.
介绍了钢筋滚制等强直螺纹接头（FP接头）的特点，阐述了该项技术的施工工艺、操作过程和质量检验要求以及推广的价值，并指出了施工中应注意的事项。 - The software provides the various possible linear and nonlinear models as well as verification for segment design specification, and is suitable for two segment assembling types with the straight joint and the staggered joint.
软件考虑了各种可能的线性和非线性模式以及规范验算方法，实现了计算的图形化输入，适用于管片通缝和错逢拼装计算。 - After that, we gave a mathematical formula and its computer program for JRC modified straight edge which contain scale effect of joint roughness coefficient.
考虑JRC的尺寸效应，推导JRC修正直边法的数学表达式，编译计算机常用程序。 - Describes a J shaped stack developed to meet the requirement of smoke emission standard of oil fired boilers, which consists of a slope tee, a straight pipe, an expansion joint, an explosion flap, a rain drain pipe and a down pipe.
为满足燃油锅炉的烟气排放要求，设计了J型烟囱，它由斜三通、直管、膨胀节、防爆门、雨漏、落水管等组成； - Especially, using the straight thread splices with upset ends ( SA class) simplified greatly the construction of column beam joint.
特别是采用了SA级的镦粗直螺纹钢筋接头，大大简化了梁柱接头的构造，并且方便了施工。 - In order to braze hydraulic guide tubes for instance the straight to elbow muff joint, a semiautomatic brazing machine with multiple air-acetylene flame nozzles has been developed which can provide mechanical operation for brazing process and guarantee the brazing quality.
针对液压导管中直管与弯管或直管与直管套接的钎焊接头，研制了空气-乙炔半自动火焰钎焊机。使用多嘴火焰焊枪，可实现机械化操作，并保证焊接质量。 - Research and analyze working principle and disposition pattern of traditional P2P traffic control technologies, then make a comparative analysis of their advantages and disadvantages. And make rational use of the two to design straight bypass joint disposition pattern. 3.
研究分析了传统的P2P流量控制技术的工作原理和部署方式，对直路丢包和旁路干扰控制技术进行对比分析，并合理结合两种技术设计了直路旁路联合部署方式。 - In this paper, mechanical model of the straight tenon-mortise joint is studied, according to theoretical analysis, and reinforcing method for tenon-mortise joint with dampers are also discussed.
本文通过理论分析，对直榫节点的力学模型进行了研究，并对采用阻尼器加固榫卯节点的方法进行了探索。 - Regarding long straight pipes, the design replaces elastic analysis with stress analysis and uses directly buffed cold installation and preheating installation without expansion joint to replace compensatory directly buried method and cancels most compensators and anchor blocks trying to reduce construction cost and duration.
针对长直管道，以应力分析方法取代了弹性分析法，以无补偿直埋冷安装及预热安装取代了有补偿直埋敷设，取消了大部分补偿器及固定墩的设置，从而降低造价、缩短工期。 - In the course of constructing the interval tunnel of metro with shield tunneling method, single lining assembling plan is popular currently, and it mainly consists of straight joint and staggered joint method.
采用盾构法修建地铁区间隧道时，单层拼装式衬砌是目前采用的主流形式，而管片拼装方式主要有通缝式和错缝式。